Button 1: Activate / Deactivate / Suspend

To activate the device and start sending position reports, press and hold the power button (Button 1) for 2 seconds. The LED will light up, and will show a solid green light to indicate your unit is active and tracking is enabled.

To deactivate the unit, press and hold the power button for 2 seconds again. The Power LED will turn off, indicating that the unit is now deactivated. When deactivated, no position reports, waypoints or messages will be sent.

You can also temporarily suspend tracking by a short press of the power button. When tracking is suspended, the LED will flash quickly - to resume tracking, press the power button again, and the LED will show a solid green light.

The power LED indicator flashes according to the following indicator modes.

  • Intermittent green flash - running on battery power
  • Solid green - using external power
  • Off - in Shipping Mode, Stealth Mode, or battery has run out and there's no external power

Note : When tracking is temporarily suspended, no routine tracking positions will be sent - however, you can still send alerts and waypoints (see 2 & 3 below).

Button 2: Watch Mode

Watch Mode will ensure an automatic alert is raised if your provider decides your activity is abnormal (irrespective of whether you raise a manual SOS). Different providers may monitor activity in different ways - for example, some may only alert if tracking data stops being reported for a certain amount of time, others may employ more sophisticated monitoring such as altitude level drops and extreme bank/roll monitoring. Please speak to your provider to determine what activity is monitored when you enable Watch Mode.

To activate Watch Mode, press the Watch button (Button 2). The LED will start flashing quickly. At this point the IndigoDUO is sending a message to your provider, requesting that you wish to be ‘watched’, and awaiting confirmation that their system has received your watch request.

Once IndigoDUO receives confirmation from your provider, the Watch button LED will show a solid green light. You are now actively being watched, and if routine tracking information stops being sent, an automatic alert will be raised.

To deactivate Watch Mode, press and hold the Watch button for 2 seconds. The LED will start flashing slowly. At this point the IndigoDUO is sending a message to your provider, requesting that you do not wish to be ‘watched’ any longer, and is awaiting confirmation that their system has received your ‘stop watch’ request.

Once IndigoDUO receives confirmation from your provider, the LED will turn off. You are now back in Normal Operating Mode, and your provider is not actively monitoring your transmissions.

Button 3: Waypoint/Mark

Sometimes you may wish to mark an interesting spot or waypoint for later review. The IndigoDUO enables you to do this easily by using the Mark button.

Pressing the Mark button will make all four LED button lights flash, requiring you make a choice of which ‘type’ of waypoint you wish to mark (1, 2, 3 or 4). If you press button 1, then the point will be registered as type 1. Your provider will display these waypoints on the mapping for later review.

Examples of waypoint types can be, for example, oil wells, beehives, fires and other points depending on your mission.

Once a waypoint type has been chosen, a GPS fix will be taken at your current location and sent, along with the waypoint type, for later review in MiTrac’s web interface.

Button 4: SOS Alert

Sending an Alert

Pressing the red Alert button will trigger an alert message to be sent to your provider, and the LED will flash constantly indicating your IndigoDUO unit is now in Alert Mode.

Depending on the arrangements you have with your provider, this may alert your own predefined first responders, or emergency services. Check with your account manager if you are unsure who will be alerted in the event of an Alert button press.

Note: Whilst in Alert Mode, your IndigoDUO will be transmitting tracking information based on your 'Distress Profile'

Cancelling an Alert

If you have inadvertently set off an alert, you can send an alert cancellation message. To cancel your alert, you can either:

  • Press and hold the alert button for 4 seconds
  • Deactivate your IndigoDUO unit (see button 1)

Depending on the arrangements you have made with your provider, this may completely cancel the alert automatically, or you may still be required to take further action to confirm you are safe and the alert was accidental - please check with your account manager if you are unsure.

Reset

In rare situations, you may be requested by support staff to perform a ‘hard reset’ of your IndigoDUO unit. To do this, hold down the Power button (button 1) for 8 seconds.

When the unit has been successfully reset, all of the lights will flash 3 times and IndigoDUO will beep to indicate that it's ready for use again. Resetting can take up to 60 seconds after the buttons have been released.